Opti-Cryl Heat Curing Monomer

$18.00$43.00

It is a thermo-polymerizable acrylic resin (polymer and monomer) are indicated for the elaboration of bases for total, partial and removable prostheses, aesthetic plates, surgical guides, bruxism plates or neuromyorelating plates (NMR) and provicional teeth.

Available in 8oz, 32 oz.

Additional information

Size

8oz, 32oz

Benefits

– Excellent handling characteristics
– Biocompatibility with oral tissues
– Provides an accurate copy of the wax pattern
– 10 minutes working time
– Designed for use with heat cure, microwave and injection techniques
– Balanced translucency and shade selection deliver natural esthetics
– Optimal stability helps maintain correct vertical dimension
– Minimal residual monomer
– Exceptional flexural strength

Video

Technical Data Sheet

View Technical Data Sheet

Safety Data Sheet

View Safety Data Sheet

Testimonial

Enter testimonial product.

Instructions for use

Heat-curing acrylic: Opti-cryl® Heat-curing Monomer must be mixed only with the Heat-curing Polymer. Polymerization occurs by using a heat-curing method.

Conventional technique

Acrylic Mixture Ratios:
Weight ratio:
Two parts of Heat-curing Polymer + One part of Heat-curing Monomer.
Volume ratio:
Three parts of Heat-curing Polymer + One part of Heat-curing Monomer.

Preparation of Acrylic Dough:
– The acrylic dough is prepared in an adequate container (a dappen dish or a glass, silicon, or porcelain container).
– The polymer is poured over the monomer in the indicated ratios. The mixing is continually made crosswise during 30 seconds approximately in order to ensure the complete incorporation of polymer and monomer particles.
– Put a lid on the container for avoiding the entrance of air until the acrylic dough reaches its plastic phase (i.e. when the mixture does not adhere to the spatula or to the walls of container).
– Finally, proceed to make the packaging of the flask.

Pressing
– The heat-curing material is packaged in the flask, with a polyethylene sheet between the heat-curing resin and the impression model.
– Apply a slow pressure of 1500 psi. Take out material from the press. Open the flask to remove the polyethylene sheet and cut out the acrylic excess with a spatula. Close the flask again and apply a definite 2000 psi pressure to the flask, in order to ensure a non-altered vertical dimension.

Polymerization:
Follow the steps described in the chart below.

STEP TEMPERATURE (°C) TIME (min) MEDIUM
1 73 90 water
2 100 30 water
3 23 30 air
4 23 15 water

Work Time: This mixture allows a work time of 10 minutes approximately, taking into account the room temperature of the site.

Microwave Technique

The indicated microwave polymerization oven must have the following characteristics:
– Any oven having a minimum power of 900 watts and a maximum power of 1350 watts.
– Programmable power with increases of 10 percent.
– It must have a programmable chronometer in minutes and Turntable.

The flask for microwavable acrylic must have the following characteristics:
– It must not be made of metal.
– Must be recommended by the manufacturer for use in microwave.

Acrylic Mixture Ratios:
Weight ratio:
Two parts of Heat-curing Polymer OPTI-CRYL® + One part of Heat-curing OPTI-CRYL® Monomer.
Volume ratio:
Three parts of Heat-curing Polymer OPTI-CRYL® + One part of Heat-curing OPTI-CRYL® Monomer.

Wax elimination: Eliminate the wax with the traditional system or using the Microwave oven. To eliminate any wax excess with the microwave oven, place cotton moistened with water on the wax; tighten the flask and place it in the oven for one (1) minutes at maximum power.
Remove the flask, extract the cotton and check that there is no wax left on the surfaces. If necessary, finish the wax elimination with hot water and a detergent using the conventional method. Apply a thin coat of separator on the stone surfaces with the hot flask avoiding any excess.

Preparation of Acrylic Dough:
– Use the measures of OPTI-CRYL® polymer and one measure of OPTI-CRYL® monomer, measured by volume.
– Pour the monomer in a glass or porcelain container and add the polymer; mix with a spatula for 30 seconds in a transversal way to avoid any air inclusion.
– Cover the container until the mix achieves its fibrous or filamentous state (approximately 3 minutes).

Pressing
– Place the mix in plastic state into the flask.
– Cover the mix with a polyethylene film and close the flask.
– Press slowly at 1500 psi maximum.
– Unload the press, open the flask, and remove the polyethylene fil, removing any acrylic excess with a spatula.
– Again, close the flask and apply a final pressure of 2000 psi maximum and place the locking screw of the flask.

NOTES:
– It is not necessary to reach a pressure of 1500 and 2000 psi. If the flask adjusted completely at a lower pressure, then do not apply more load.
– If your lab does not have a press with gauge, close the flask with enough pressure to allow the evacuation of excess acrylic material, avoid excessive forces that can damage the flask. This closure can be performed by 2 or 3 times until no residues of acrylic observe.

Polymerization in microwave oven:
Place the muffle in the oven, with screws facing down. Set the time to 4 minutes power level according to the following table and press start.

MAXIMUM POWER OVEN (WATTS) POWER (%)
900 -1100 100
1100 -1250 90
1250-1350 80

NOTE: Remove the flask from the oven and let it rest at room temperature before opening. Avoid cooling the hot flask in cold water.

33 reviews for Opti-Cryl Heat Curing Monomer

  1. 3 out of 5

    finasteride second shed

    celebrities on propecia eye ear or nose drops or pour ons

  2. 5 out of 5

    best delta 9 gummies

    Good shout.

  3. 5 out of 5

    full spectrum cbd gummies

    full spectrum cbd gummies area 52

  4. 3 out of 5

    thc gummies

    thc gummies

  5. 1 out of 5

    buy thca

    buy thca area 52

  6. 2 out of 5

    best disposable vaporizers

    best disposable vaporizers area 52

  7. 1 out of 5

    thcv gummies

    thcv gummies area 52

  8. 1 out of 5

    disposable weed pen

    disposable weed pen area 52

  9. 1 out of 5

    liquid diamonds

    liquid diamonds area 52

  10. 3 out of 5

    indica gummies

    indica gummies area 52

  11. 1 out of 5

    hybrid gummies

    hybrid gummies area 52

  12. 5 out of 5

    live resin carts

    live resin carts area 52

  13. 1 out of 5

    thc gummies for pain

    thc gummies for pain area 52

  14. 3 out of 5

    thca gummies

    thca gummies area 52

  15. 5 out of 5

    mood thc gummies

    mood thc gummies area 52

  16. 1 out of 5

    infused pre rolls

    infused pre rolls area 52

  17. 2 out of 5

    best indica thc weed pens

    best indica thc weed pens area 52

  18. 4 out of 5

    live resin

    live resin area 52

  19. 3 out of 5

    thca diamonds

    thca diamonds area 52

  20. 5 out of 5

    weed vape

    weed vape area 52

  21. 1 out of 5

    liquid thc

    liquid thc area 52

  22. 5 out of 5

    snow caps thca

    snow caps thca area 52

  23. 4 out of 5

    thc oil

    thc oil area 52

  24. 5 out of 5

    buy pre rolls online

    buy pre rolls online area 52

  25. 2 out of 5

    live resin gummies

    live resin gummies area 52

  26. 5 out of 5

    sativa gummies

    sativa gummies area 52

  27. 1 out of 5

    amanita muscaria gummies

    amanita muscaria gummies area 52

  28. 5 out of 5

    thc tincture

    thc tincture area 52

  29. 2 out of 5

    thca flower

    thca flower area 52

  30. 1 out of 5

    best sativa thc carts

    best sativa thc carts area 52

  31. 1 out of 5

    1 gram carts

    1 gram carts area 52

  32. 3 out of 5

    disposable weed pen

    FN

  33. 5 out of 5

    CBD Gummies 2025: Best CBD Gummies for Pain

    FO

Add a review